Note: Don't do this with rewritable discs. But, be careful that you don't cross over the line and into the data (see illustration). The lighter area wasn't recorded and has no data, so it's safe for labeling. The inner hub area, though small, is a perfect location for labeling.Īlternatively, if you didn't use the entire capacity of the disc during recording, you can write in the area that wasn't burned. Instead, label the disc where no data is recorded. However, if you are archiving precious family memories or other highly important data, don't write on top of that disc! ![]() You'll have a new favorite band before the ink has time to ruin it. ![]() If all you're doing is making a music disc for your car, it really doesn't matter. There is no apparent reason for the corruption other than the ink used to label the disc.Ĭonsider the purpose of the disc. Various postings are surfacing across the internet from professionals and hobbyists alike, reporting that over time permanent ink has made their properly stored discs unusable. There is growing concern that components of ink from markers previously thought of as "safe," such as many commonly used permanent markers, will eventually penetrate and be absorbed by the inner layers of your disc, damaging the surface where the data is stored and rendering the disc unplayable. The tip won't harm your disc, but the ink might. Although this might not happen every time, it would be worth not taking the risk.īut what about those soft tipped permanent markers that everyone uses? Can those cause harm, too? Possibly. Anything that puts high point-pressure on the surface can damage the delicate layers beneath. Obviously, ballpoint or hard tipped pens can scratch the surface of the disc where the data reside, possibly rendering it unplayable. So what harm will come from writing on discs? Last, some CD-Rs have additional protective layers on the top of the disc, for example those with a " white printable surface." These CD-Rs, while more expensive, are far less susceptible to damage. Second, it should go without saying (but we'll say it anyway) that you should never write on or label a double sided DVD - since both sides are read by the laser. However, this does not make it immune to damage. The data layer in a DVD is more protected than that of a CD. There are a few side notes that we cannot ignore here: The first being that CD-Rs and DVDs are constructed differently. Damage to the top of the disc can destroy the data all together. On some CD-Rs, the data layer is under nothing but a thin layer of lacquer. However, most people don't realize that the tops of discs are just as prone to damage as the bottom - if not more so! Although you can physically see the shiny data layer from the bottom of a CD-R, it is actually applied to the TOP side of the disc, just under the label. Scratches, fingerprints, and other debris can stop the laser from reading the data. Most people know that it is very important to keep the bottom of your discs clean and scratch free. The data appear as marks or pits that either absorb light from the laser beam or transmit the light back to the laser/photosensor by way of the shiny metal reflective layer. The plastic is there to carry the data layer - the shiny metal you can see when you look at the bottom of a disc. In order to understand why certain markers and pens can harm your CD-Rs and DVDs, we first need a basic lesson on the physical properties that make up the disc:ĬD-Rs and DVDs are made mostly of polycarbonate substrate, or plastic. ![]() But you do have to be careful of the kind of writing instrument you use to do so. Now, we're not saying you can't label your discs. The damage won't happen today, or even next month, but at some point the ink will leach into the reflective layer of the disc and it'll be the end of your data. ![]() It's also a great way to assure that the disc won't be readable later on. If the entire sheet of labels is misaligned, try adjusting the top and/or left margins in the layout settings.The easiest way to label a CD-R is to whip out that permanent marker and write directly on the disc. Select print job settings: In the program you are creating the labels with, set the print quality to Normal and the paper type to Plain or Labels, if available. Load them into the paper tray on top of a stack of approximately 25 sheets of plain Labels to separate from the backing sheet. Load label sheets so they properly feed into the printer: Fan the label sheets, being careful not to bend any corners or cause Place the test sheet behind the label sheet, and then hold them up to a bright light to confirm the text is aligned and large Of the paper, and then note where the mark is according to the printed side of the test sheet. Test the print job on plain paper first: To confirm how to load the label sheet in the paper tray, make a mark on one side
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |